To close fire doors in an emergency and prevent the spread of fire and smoke. Fitted with an integral manual release button, allowing the door to be closed without operating the fire alarm. Supplied with a door mounting keeper plate
Key Features Low profile design 200N holding force Easy cable entry & exit A.C. or D.C. options Push button release/test Floor mounting bracket available Anti-residual magnetism feature D.C. version polorised and suppressed featu
Key Features Low profile design 200N holding force Easy cable entry & exit A.C. or D.C. options Push button release/test Floor mounting bracket available Anti-residual magnetism feature D.C. version polorised and suppressed feature
Up to 242 address per loop and definition of devices Up to 1.2Km Class A loop or Class B radial Optional loop expander up to 1Km Class B (P-9903) Built-In loop isolator Addressable Card Switch key interface module Reset bottom Built-in watch dog circuit Plug –in type easy to install
Works on D7050 and F220 detector heads Uses ½ in. (1.3 cm) conduit to reach high-mounted detectors Light weight for ease in handling
Adds four Class B (Style B) or Class A (Style D) initiating circuits to the FPD‑7024 FACP For use with normally‑open (NO) or normally‑closed (NC) alarm contacts Compatible with two‑wire or four‑wire smoke detectors Up to 20 two‑wire smoke detectors per circuit Easy installation due to plug‑in design and screw terminal circuit connections No programming...
Use with the FPA‑1000 Analog Addressable Fire Panels or FPD‑7024 FACPs LED indicates power, trouble, and zone status LED annunciates eight individual zones expandable to 64 zones Aesthetically appealing appearance, mounts flush to electrical box in either surface or flush mounted configurations UL Listed
Compatible with the FPD‑7024 FACP Two‑line, 32‑character, alphanumeric LCD display Status LEDs identify alarm, trouble, supervisory, and silenced conditions Address setting by jumper Remotely control system commands and programming Passcode protection controls system access Low profile design
Non-conductive at voltage of 20 kV Expandable with other Fixed Extension Pole Extension for the SOLO100 Telescopic Access Pole
Non-conductive at voltage of 20 kV Expandable with up to three SOLO101 Fixed Extension Poles
Suitable for a wide range of detector sizes Adjustable color-coded grips rotate to fit different sized detectors Universal joint ensures tool remains parallel with ceiling
Differentiated fault detection and localization on the LSN and LSN improved field bus Professional installation check for handover including documentation Basic functionality testing of peripherals (for sounders and beacons)
Touch-sensitive, spring-loaded mechanism for effective, economic aerosol delivery Clear cup allows view of detector LED Strong and durable modern plastics technology for long life and minimal weight Compatible with SOLO100 and SOLO101 Poles
Operating status display with multi-color LED Automatic detector recognition with infrared sensors Automatic switch-off after 5 min. standby time Automatic switch-off in case of battery overvoltage Enters standby mode after 120 seconds of use Microprocessor maintains constant heat and airflow even with variations in battery voltage
DIP switch configuration for "Link-Fault-Pass-Through", link down alarm, speed, duplex mode 768K bits buffer memory Full wire-speed forwarding rate Alarms for power and port link failure by relay output Redundant power inputs with Terminal Block and DC Jack
The Power Supply is protected against pole reversal and overvoltage. The output voltage is monitored and regulated via the thermal sensor. If there is a fault, the FAULT output drops to 0 V. A green LED on the Universal Power Supply indicates operativeness.
The Power Supply Brackets are installed in wall-mount housings and accommodate one Power Supply. The Power Supply Unit is immediately ready for operation via the prewired plug connection. The brackets are made of glass-fiber-reinforced plastic and have a thermal sensor as well as a T10A mains fuse.
The HMP 0003 A Mounting Plate is used in both the large FBH 0000 A and FHS 0000 A mounting frames. The mounting plate is required to install interface modules, external device controllers, relays and other components. It can be fitted with a distributor rail.
The large mounting frame is equipped with a distributor rail in accordance with EN 60715 for attaching series terminals. The large mounting frame can be used as an alternative to FBH 0000 A for the following frame installation housings: - CPH 0006 A - MPH 0010 A - EPH 0012 A.
The small mounting frame is required for the frame installation housings: - PSF 0002 A Power Supply, Frame Installation - USF 0000 A Universal Housing Small, Frame Installation.
Material Plastic, ABS Color Anthracite gray, RAL 7016 Dimensions Approx. 502 x 450 x 87 mm(approx. 19.8 x 17.7 x 3.4 in.)
Material Plastic, ABS Color Anthracite gray, RAL 7016 Dimensions Approx. 638 x 450 x 87 mm(approx. 25.1 x 17.7 x 3.4 in.)
Surface-mount, flush-mount or installation in 482.6 mm (19") racks Modular system
Surface-mount or installation in 482.6 mm (19") racks Modular system
Up to 64, 128, 512, 1024 or 2048 addresses on one card Up to four cards in one control panel
Plug-and-play rails Adequate for two or four modules
2.5 Amp PSU designed to meet the requirements of EN54-4. This range of PSUs includes all of the necessary monitoring and standby capability demanded by EN54-4. Each unit comes within the same size steel enclosure for ease of use, offering2.5A or 5A alarm capability.
5.0 Amp PSU designed to meet the requirements of EN54-4. This range of PSUs includes all of the necessary monitoring and standby capability demanded by EN54-4. Each unit comes within the same size steel enclosure for ease of use, offering2.5A or 5A alarm capability.
Key Features Remote control of output Choice of switching options LED indication Mains transient protection Fail safe operation
The enhanced TR range of power supplies have been specifically designed for access control applications that require remote control of the power supply output. TR power supply units are typicallymused to power door retainers with a link to the fire panel in order tomswitch off the output to the doors upon the activation of a fire alarm.
• Loop powered • Soft addressed • Integral short circuit Isolator • Single address • High visibility LED • Can be programmed to monitor multiple remote sensors • Fits on to a standard singl gang back box • Aesthetically pleasing